The Judgement Before the Chart
15CrMoG and 12Cr1MoVG are grades written into a Chinese seamless tube specification for high-pressure boiler service. WP11 and WP22 are grades written into the ASME/ASTM specification for wrought fittings. There is no one-to-one correspondence between the two lists that can be certified from the grade names, and 12Cr1MoVG must not be recorded as equivalent to any single ASTM grade: its designation carries vanadium, and a chart pairing it with a grade that does not is answering a different question.
The usual failure is not a wrong number. It is a table that looks right — a Chinese tube grade in one column, an ASTM fitting grade in the next, and the row closed with the word "equivalent". It survives until someone asks which edition, which product form and which clause, and then it has to be rebuilt.
Scope First: Three Specifications and One Order
The comparison runs across three specifications and one purchase order, and they are not the same kind of document. GB/T 5310-2023《高压锅炉用无缝钢管》 covers seamless steel tubes for high-pressure boilers. It is a recommended national standard, currently in force, published on 2023-09-07 and effective from 2024-04-01; it fully replaces GB/T 5310-2017, and it falls under the national steel standardization technical committee. ASTM A234/A234M — the page version consulted here is A234/A234M-26 — covers wrought carbon steel and alloy steel fittings for moderate and elevated temperature service. ASTM A335/A335M, in its -24 page version, is titled as the specification for seamless ferritic alloy-steel pipe for high-temperature service.
The first question on the sheet is therefore not a chemistry question. It is which of these documents the item on the truck must satisfy. A tube specification does not become a fitting specification because a grade name in one resembles a grade name in the other; the document the order invokes is the one whose clauses get compared, and the other two are context.
What the Chinese Grades Are Written Into
Both 15CrMoG and 12Cr1MoVG belong to the grade list of GB/T 5310-2023, a standard whose title limits its subject to high-pressure boiler seamless tube. That is narrower than "Chinese chromium-molybdenum steel", and it is the claim that matters where the line item says "15CrMoG" but the drawing describes a fitting.
The edition is not a formality. GB/T 5310-2023 fully replaces GB/T 5310-2017 from 2024-04-01. A certificate citing the older edition is not automatically defective — the material may have been ordered earlier — but it is evidence about a different text, and that belongs in the file, not in a footnote.
On the second grade, one point deserves stating plainly. 12Cr1MoVG contains vanadium, and that is not a detail to be averaged away. A grade that carries vanadium and one that does not are different alloy designs, whatever the chromium and molybdenum figures look like side by side. A mapping that has to delete a deliberate alloying addition is not a mapping.
Where WP11 and WP22 Actually Sit
WP11 and WP22 are grades of A234/A234M, whose scope is wrought carbon steel and alloy steel fittings for moderate and elevated temperature service. A fitting marked WP22 is a fitting: formed, heat treated, tested and marked as a fitting. The pipe side of the same alloy families is a separate document, A335/A335M, with its own designations and its own requirements.
This is why a chromium-molybdenum spool is rarely a single paper trail. Pipe and fittings of the same alloy family arrive with two specifications, possibly two designations and two sets of certificates, and the sheet needs a column for each. Treating a fitting grade as a short form of a pipe grade conceals exactly the difference inspection is meant to find.
The Comparison Sheet That Can Be Audited
The table below is a set of blanks with a destination for each. Filling a cell means naming a clause in a specific edition; a cell that cannot be closed that way is an open item, not a passed check. No composition limits or allowable stresses are reproduced here: values copied from an unattributed chart are numbers nobody can trace.
| Check item | GB/T 5310-2023 (boiler tube) | A234/A234M-26 (wrought fittings) | A335/A335M-24 (seamless pipe) | What the sheet records |
|---|---|---|---|---|
| Status and edition | Recommended, current; published 2023-09-07, effective 2024-04-01, replaces GB/T 5310-2017 | Edition cited by the order | Edition cited by the order | Number, edition and date on every line |
| Product form | Seamless tube for high-pressure boilers | Wrought carbon and alloy steel fittings | Seamless ferritic alloy-steel pipe | The form actually being bought |
| Grade designation | 15CrMoG, 12Cr1MoVG as written | WP11, WP22 as written | Pipe designations as written | Both designations verbatim |
| Chemical composition | Grade table of the edition in force | Grade table of the specification | Grade table of the specification | Element, limit, basis, clause |
| Analysis basis | Heat or product analysis as defined in the text | As defined in the text | As defined in the text | Which basis the certificate reports |
| Tensile and yield properties | As required for tube | As required for fittings | As required for pipe | Specimen form, orientation, test temperature |
| Impact testing | Whether required, and for which condition | Same question | Same question | Required or not, with clause |
| Delivery condition | Heat treatment the tube standard recognizes | Condition the specification requires | Condition the specification requires | Condition stated on the certificate |
| Marking and testing | Rules of the standard | Rules of the specification | Rules of the specification | Which tests the order invokes |
Two rows decide most substitutions and are the most often left blank: product form, and edition.
Where the Mapping Stops, and Where the Order Takes Over
The boundary has three lines, and each is closed by reading rather than by choosing a word.
The first is product form. A seamless tube standard qualifies tube. Where the item is a fitting, the fitting specification governs; a tube grade name on the drawing does not transfer the tube clauses onto the fitting.
The second is the grade itself. Grades differ in which elements they specify and limit, and a vanadium-bearing designation compared against one without vanadium is a comparison between two alloy designs. Whether a particular Chinese grade corresponds to WP11, to WP22, or to neither is to be established from the grade tables of GB/T 5310-2023 and A234/A234M read side by side — element by element, basis by basis, condition by condition. That reading remains an open item here and stays open until it is done against the standard texts; a supplier chart does not close it.
The third is the edition. A sheet built on a superseded edition is a sheet built against a text withdrawn in full, and each figure should carry the edition it came from.
Where the documents leave room, the purchase order closes it. Name the standard number and edition, name the product form, write the grade designation exactly as the governing text writes it, and state which route applies where the specification offers more than one. Inspection then verifies against something concrete rather than a name two parties read differently. Whether a difference matters is a design decision, and it belongs to the engineer and the purchaser.
The power plant piping parts and seamless butt welding pipe fittings pages set out what is normally ordered. Send the standard number, edition and product form via the inquiry page, so the offer is written against the same document the comparison was built from.
Sources
Besoin d'un devis pour les produits cités dans cet article ?
Envoyez vos spécifications, notre équipe répondra sous un jour ouvré.
Envoyer RFQDevis sous 4 h
Produits abordés dans cet article
Besoin d'un devis ? Envoyez vos spécifications, notre bureau tuyauteries répond sous 4 heures ouvrées.
TubeASTM A106/A53, API 5L, ASTM A192, DIN17175 ST35.8/37, DIN1629 ST52, ASTM A210, ASTM A335, ASTM A179
Té
TéÀ lire également
TechniqueChinese 20# and Q355B Fittings vs ASTM A234 WPB: What to Check Item by Item
Comparing 20# and Q355B with ASTM A234 WPB is not a grade-equivalence question. A clause-by-clause checklist for scope, chemistry, properties and heat treatment.
TechniqueBubble Emission vs Hydrostatic Leak Testing for Fittings
Choose between ASTM E515 bubble emission and ASTM E1003 hydrostatic leak testing for fittings: principles, sensitivity, and procurement checks.
TechniqueAbrasion and Wear Testing for Lined Pipe Fittings
Understand ASTM G65 and G99 for abrasion and wear testing of lined pipe fittings. Learn how to interpret results, avoid common pitfalls, and specify tests in your RFQ.
